1926.950(a)

Application. The occupational safety and health standards contained in this Subpart V shall apply to the construction of electric transmission and distribution lines and equipment.

1926.950(a)(1)

As used in this Subpart V the term "construction" includes the erection of new electric transmission and distribution lines and equipment, and the alteration, conversion, and improvement of existing electric transmission and distribution lines and equipment.

1926.950(a)(2)

Existing electric transmission and distribution lines and electrical equipment need not be modified to conform to the requirements of applicable standards in this Subpart V, until such work as described in paragraph (a)(1) of this section is to be performed on such lines or equipment.

1926.950(a)(3)

The standards set forth in this Subpart V provide minimum requirements for safety and health. Employers may require adherence to additional standards which are not in conflict with the standards contained in this Subpart V.

..1926.950(b)

1926.950(b)

Initial inspections, tests, or determinations.

1926.950(b)(1)

Existing conditions shall be determined before starting work, by an inspection or a test. Such conditions shall include, but not be limited to, energized lines and equipment, conditions of poles, and the location of circuits and equipment, including power and communication lines, CATV and fire alarm circuits.

1926.950(b)(2)

Electric equipment and lines shall be considered energized until determined to be deenergized by tests or other appropriate methods or means.

1926.950(b)(3)

Operating voltage of equipment and lines shall be determined before working on or near energized parts.

1926.950(c)

Clearances. The provisions of paragraph (c) (1) or (2) of this section shall be observed.

1926.950(c)(1)

No employee shall be permitted to approach or take any conductive object without an approved insulating handle closer to exposed energized parts than shown in Table V-1, unless:

1926.950(c)(1)(i)

The employee is insulated or guarded from the energized part (gloves or gloves with sleeves rated for the voltage involved shall be considered insulation of the employee from the energized part), or

1926.950(c)(1)(ii)

The energized part is insulated or guarded from him and any other conductive object at a different potential, or

..1926.950(c)(1)(iii)

1926.950(c)(1)(iii)

The employee is isolated, insulated, or guarded from any other conductive object(s), as during live-line bare-hand work.

1926.950(c)(2)

-

1926.950(c)(2)(i)

The minimum working distance and minimum clear hot stick distances stated in Table V-1 shall not be violated. The minimum clear hot stick distance is that for the use of live-line tools held by linemen when performing live-line work.

1926.950(c)(2)(ii)

Conductor support tools, such as link sticks, strain carriers, and insulator cradles, may be used: Provided, That the clear insulation is at least as long as the insulator string or the minimum distance specified in Table V-1 for the operating voltage.

     TABLE V-1 - ALTERNATING CURRENT -  MINIMUM DISTANCES
____________________________________________________________________
                                   |
Voltage range (phase to to phase)  |  Minimum working and clear hot
       (kilovolt)                  |       stick distance
____________________________________|_______________________________
2.1 to 15 ..........................|      2 ft. 0 in.
15.1 to 35 .........................|      2 ft. 4 in.
35.1 to 46 .........................|      2 ft. 6 in.
46.1 to 72.5 .......................|      3 ft. 0 in.
72.6 to 121 ........................|      3 ft. 4 in.
138 to 145 .........................|      3 ft. 6 in.
161 to 169 .........................|      3 ft. 8 in.
230 to 242 .........................|      5 ft. 0 in.
345 to 362 .........................|   (1)7 ft. 0 in.
500 to 552 .........................|  (1)11 ft. 0 in.
700 to 765 .........................|  (1)15 ft. 0 in.
____________________________________|_______________________________
 Footnote(1) NOTE: For 345-362 kv., 500-552 kv., and 700-765 kv.,
minimum clear hot stick distance may be reduced provided that such
distances are not less than the shortest distance between the
energized part and the grounded surface.

1926.950(d)

Deenergizing lines and equipment.

1926.950(d)(1)

When deenergizing lines and equipment operated in excess of 600 volts, and the means of disconnecting from electric energy is not visibly open or visibly locked out, the provisions of paragraphs (d)(1) (i) through (vii) of this section shall be complied with:

1926.950(d)(1)(i)

The particular section of line or equipment to be deenergized shall be clearly identified, and it shall be isolated from all sources of voltage.

1926.950(d)(1)(ii)

Notification and assurance from the designated employee shall be obtained that:

..1926.950(d)(1)(ii)(a)

1926.950(d)(1)(ii)(a)

All switches and disconnectors through which electric energy may be supplied to the particular section of line or equipment to be worked have been deenergized;

1926.950(d)(1)(ii)(b)

All switches and disconnectors are plainly tagged indicating that men are at work;

1926.950(d)(1)(ii)(c)

And that where design of such switches and disconnectors permits, they have been rendered inoperable.

1926.950(d)(1)(iii)

After all designated switches and disconnectors have been opened, rendered inoperable, and tagged, visual inspection or tests shall be conducted to insure that equipment or lines have been deenergized.

1926.950(d)(1)(iv)

Protective grounds shall be applied on the disconnected lines or equipment to be worked on.

1926.950(d)(1)(v)

Guards or barriers shall be erected as necessary to adjacent energized lines.

1926.950(d)(1)(vi)

When more than one independent crew requires the same line or equipment to be deenergized, a prominent tag for each such independent crew shall be placed on the line or equipment by the designated employee in charge.

..1926.950(d)(1)(vii)

1926.950(d)(1)(vii)

Upon completion of work on deenergized lines or equipment, each designated employee in charge shall determine that all employees in his crew are clear, that protective grounds installed by his crew have been removed, and he shall report to the designated authority that all tags protecting his crew may be removed.

1926.950(d)(2)

When a crew working on a line or equipment can clearly see that the means of disconnecting from electric energy are visibly open or visibly locked-out, the provisions of paragraphs (d)(i), and (ii) of this section shall apply:

1926.950(d)(2)(i)

Guards or barriers shall be erected as necessary to adjacent energized lines.

1926.950(d)(2)(ii)

Upon completion of work on deenergized lines or equipment, each designated employee in charge shall determine that all employees in his crew are clear, that protective grounds installed by his crew have been removed, and he shall report to the designated authority that all tags protecting his crew may be removed.

1926.950(e)

Emergency procedures and first aid.

1926.950(e)(1)

The employer shall provide training or require that his employees are knowledgeable and proficient in:

1926.950(e)(1)(i)

Procedures involving emergency situations, and

1926.950(e)(1)(ii)

First-aid fundamentals including resuscitation.

..1926.950(e)(2)

1926.950(e)(2)

In lieu of paragraph (e)(1) of this section the employer may comply with the provisions of 1926.50(c) regarding first-aid requirements.

1926.950(f)

Night work. When working at night, spotlights or portable lights for emergency lighting shall be provided as needed to perform the work safely.

1926.950(g)

Work near and over water. When crews are engaged in work over or near water and when danger of drowning exists, suitable protection shall be provided as stated in 1926.104, or 1926.105, or 1926.106.

1926.950(h)

Sanitation facilities. The requirements of 1926.51 of Subpart D of this part shall be complied with for sanitation facilities.

1926.950(i)

Hydraulic fluids. All hydraulic fluids used for the insulated sections of derrick trucks, aerial lifts, and hydraulic tools which are used on or around energized lines and equipment shall be of the insulating type. The requirements for fire resistant fluids of 1926.302(d)(1) do not apply to hydraulic tools covered by this paragraph.